Guide · Planning your kitchen

Choosing kitchen worktops: laminate, solid wood, quartz or granite

Choose the material for how you cook and how much care you will give it, then check the depth, thickness, joints and cut-outs before you order or book fitting.

Updated 9 November 2026 · 7 min read

The worktop takes more daily wear than anything else in a kitchen. It has to cope with hot pans, wet cloths, knives, spills and heavy shopping bags, and it sets the look of the whole room. The right choice depends on three things: how you cook, how much care you are willing to give the surface, and your budget, including fitting.

In short: laminate is the most affordable and easiest to live with, solid wood is warm and repairable but needs regular oiling, and stone or engineered stone such as quartz and granite are the most hard-wearing but cost more and need specialist templating and fitting. Solid surface materials sit between them, with seamless joints and integrated sinks.

You can compare worktops and related products in the countertops range. The sections below explain how the materials differ and what to check before you buy.

Worktop materials compared

MaterialGood pointsWatch out forCare
LaminateAffordable, many colours and stone or wood effects, easy to wipeCan scorch, chip at edges and swell if water gets into joints or cut edgesWipe with mild detergent; use trivets and boards
Solid wood (oak, beech, walnut)Warm look, can be sanded and re-oiled to remove marksMarks and stains if not oiled; water near the sink can cause dark marksOil regularly, especially in the first months
Quartz (engineered stone)Hard, non-porous, consistent pattern, resists stainsCan be damaged by direct high heat; heavyWipe clean; use trivets for hot pans
Granite (natural stone)Very hard, heat tolerant, each slab uniqueSome types need sealing; heavy, joints visibleWipe clean; reseal if water stops beading
Solid surfaceSeamless joins, integrated sinks possible, repairableCan scratch and mark with heatMild cleaner; light scratches can be buffed
Stainless steelHygienic, heat resistant, professional lookScratches and shows fingerprintsWipe along the grain

Laminate

Laminate is a printed decorative layer bonded to a chipboard or MDF core. Modern laminates can look very convincing as wood or stone, and they are light enough that many people fit them themselves. The weak point is water getting into the core, so the cut edges, joints and sink cut-outs must be sealed properly. Square-edged and thicker profiles look more expensive than the old rounded edge. Standard lengths of 3 m are common, with shorter no-cut pieces for islands and small runs.

Solid wood

Wood worktops are usually made from staves of oak, beech, walnut or other hardwoods glued together. They feel warm, age well and can be sanded back if they get marked. In return they need oiling: several coats before fitting, including the underside and cut edges, then a fresh coat whenever the surface starts to look dry. Avoid leaving water standing next to the sink and wipe up spills, particularly from wine, tea and acidic food. A worktop oil, such as those in the range, is what keeps the wood protected.

Quartz and granite

Quartz worktops are engineered stone made mostly from crushed quartz bound with resin. They are non-porous, so they resist stains without sealing, and the colour is consistent from slab to slab. Granite is quarried natural stone, so every slab is different, and some types benefit from sealing. Both are very heavy and usually supplied by a specialist who templates the kitchen once the units are fitted, then cuts the stone to size, including cut-outs for an undermount sink and hob. That template step adds time between ordering and fitting, so plan for a gap.

Even though stone feels tough, use trivets for hot pans: sudden high heat can mark the resin in quartz, and any stone can crack under thermal shock.

Sizes and measuring

  1. Depth: standard base units are around 560 to 580 mm deep, and worktops are commonly 600 mm deep so they overhang the doors slightly. Islands and breakfast bars need deeper or wider pieces, often 900 mm or more if people will sit there.
  2. Thickness: laminate and wood often come in 38 to 40 mm. Stone is commonly 20 to 30 mm, sometimes with a thicker edge built up.
  3. Length and joints: measure each run along the wall. Long or L-shaped kitchens need joints, so ask where they will fall and avoid joints right next to the sink.
  4. Cut-outs: note the sink, hob and any tap holes. An undermount sink needs a solid worktop material such as stone, solid surface or suitably treated wood; laminate normally suits an inset sink.
  5. Upstands and splashbacks: matching upstands finish the join with the wall and protect it from splashes.

For sink choices, see the post on choosing a kitchen sink and tap and the kitchen sinks range. If you are planning an island, the kitchen islands range and the post on planning a practical kitchen layout help with sizes and spacing.

Fitting and replacement

Worktops rest on the base cabinets, so the units must be level and secure before the worktop goes on. Replacing just the worktop is a common way to refresh a kitchen without changing the units, as long as the cabinets are sound and the new worktop matches the existing depth and sink position. Stone, long wooden runs and anything with an undermount sink are usually best left to an experienced fitter, as the cuts, joints and support need to be right first time.

For the appliances that sit under and beside the worktop, see the guide to choosing a fridge freezer.

Quick checklist

  • How you cook: heavy daily use, baking, or light use.
  • How much care you will give: oiling wood, sealing granite, or just wiping.
  • Budget including fitting, templating and cut-outs.
  • Depth, thickness and lengths measured, with joint positions agreed.
  • Sink type matched to the worktop material.
  • Upstands or a splashback planned.
  • Trivets and chopping boards in daily use.

Common questions

What is the most durable kitchen worktop?

Granite and quartz are among the hardest-wearing options for daily use, resisting scratches and stains well. Stainless steel is very durable too but shows scratches. Whatever you choose, trivets and boards extend its life.

Can I put hot pans on a quartz worktop?

It is best not to. Quartz contains resin, which can mark or discolour under direct high heat. Use a trivet or pan stand for anything straight from the hob or oven.

How often should I oil a wooden worktop?

Oil it several times when new, then whenever the surface starts to look dry or water stops beading on it. In busy areas, such as around the sink, that can mean every few months.

More guides

All guides